P2070 Intake Manifold Tuning (IMT) Valve Stuck Open Bank 1
OBD-II Trouble Code Technical Description
ASE Certified Technician
亚虎国际老虎机网站intake manifold tuning (imt) valve stuck open bank 1
What does that mean?
亚虎国际老虎机网站this diagnostic trouble code (dtc) is a generic powertrain code and applies to many obd-ii vehicles (1996-newer). that may include but is not limited to vehicles from mercedes benz, audi, chevrolet, gmc, sprinter, land rover, etc. although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
a stored code p2070 means that the powertrain control module (pcm) has detected an intake manifold tuning (imt) valve that is stuck open for engine bank two. bank 1 refers to the bank of the engine which contains the number one cylinder.
亚虎国际老虎机网站intake manifold tuning is used to restrict and control intake air as it enters individual manifold ports. not only is the volume of intake air regulated by the imt, a swirling motion is also created. these two factors aid in more effective fuel atomization. each intake manifold port is outfitted with a metal flap; not unlike the throttle plate. a single shaft runs from one end of the manifold (per engine bank) to the other and through the middle of each port. the metal flaps are attached to the shaft which will be turned (slightly) to effect opening and closing of the flaps.
the imt shaft is actuated by the pcm. some systems use an electronic over vacuum system of actuators (valves). other systems use an electronic motor to effect flap movement. the pcm sends the appropriate voltage signal and the imt valve opens and closes the valve/s to the desired degree. the pcm monitors actual valve position to determine if the system is functioning as intended.
if the pcm detects that the imt valve is stuck open, a code p2070 will be stored and a malfunction indicator lamp (mil) illuminated. mil illumination may require multiple ignition cycles with a failure.
An example of an intake manifold tuning (IMT) valve:
What is the severity of this DTC?
imt system failure could adversely affect fuel efficiency and, in rare cases, involve hardware being drawn into a combustion chamber. conditions which led to a code p2070 being stored should be rectified as quickly as possible.
What are some of the symptoms of the code?
symptoms of a p2070 trouble code may include:
- Diminished fuel efficiency
- Reduced engine performance
- Lean or rich exhaust codes
- No symptoms at all may be exhibited
What are some of the common causes of the code?
causes for this code may include:
- Binding or loose IMT flaps
- Defective IMT actuator (valve)
- Vacuum leak
- Open or shorted wiring or connectors
- Faulty PCM or a PCM programming error
What are some P2070 troubleshooting steps?
亚虎国际老虎机网站a diagnostic scanner, a digital volt/ohmmeter (dvom), and a source of vehicle specific diagnostic information will be required to diagnose a code p2070.
you may use your source of vehicle information to locate a technical service bulletin (tsb) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited. if you find one, it could yield helpful diagnostic information.
use the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. it is a good idea to write this information down before clearing the codes then test-drive the vehicle until the pcm either enters readiness mode or the code is reset.
亚虎国际老虎机网站if the pcm enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. if this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.
亚虎国际老虎机网站if the code is immediately reset, the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.
亚虎国际老虎机网站use your source of vehicle diagnostic information and the dvom to test voltage, ground, and signal circuits at the appropriate imt valve.
亚虎国际老虎机网站use the dvom to test the appropriate imt valve according to manufacturer specifications. components which do not test within maximum allowable parameters should be considered defective.
if the imt valve is functional, use the dvom to test input and output signal circuits from the fuse panel, and pcm. disconnect all controllers prior to using the dvom for testing.
- Failed IMT valves, linkages, and bushings are typically at the root of IMT related codes.
Related DTC Discussions
- Can�t get rid of p2070
Has anyone had this type of problem with their 3.6 Gm motor? Code popped up couple days ago. So I changed the intake manifold timing valve and cleared code. 2 engine cycles later and code back on. Bore is clean for valve to move freely but still getting code. Wasn't sure if wires were messed up so I...
Need more help with a P2070 code?
If you still need help regarding the P2070 trouble code, please post your question in our FREE car repair forums.
note: this information is presented for information purposes only. it is not intended as repair advice and we are not responsible for any actions you take on any vehicle. all information on this site is copyright protected.