P20E0 Exhaust Aftertreatment Fuel Pressure Sensor Circuit High
OBD-II Trouble Code Technical Description
ASE Certified Technician
exhaust aftertreatment fuel pressure sensor circuit high
What does that mean?
亚虎国际老虎机网站this diagnostic trouble code (dtc) is a generic powertrain code and applies to many obd-ii vehicles (1996-newer). that may include but is not limited to vehicles from mercedes benz, mitsubishi, etc. although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
亚虎国际老虎机网站a stored a code p20e0 in your diesel powered vehicle means that the powertrain control module (pcm) has detected excess voltage in the fuel pressure sensor circuit for the exhaust aftertreatment system.
亚虎国际老虎机网站the exhaust aftertreatment system (also called selective catalyst reduction system) is used to enhance the capabilities of the exhaust catalyst system. it may consist of one or more of these items; diesel oxidation catalyst, diesel particulate filter, reductant injection system, ammonia slip catalyst, and a nitrogen oxide (nox) trap.
the reductant injection system is typically composed of at least one reductant injector, a reductant fuel storage tank, and high-pressure reductant fuel lines. a high-pressure, electronic pump is normally situated in the tank or in the fuel supply line. an eas fuel pressure sensor allows the controller to monitor system pressure when the supply pump is activated. it is within this circuit that a malfunction has been perceived when a code p20e0 is stored.
亚虎国际老虎机网站among other things, exhaust aftertreatment systems (eas) are responsible for the injection of reductant compound/diesel exhaust fluid (def) into the exhaust in front of the diesel particulate filter, nox trap, and/or the catalytic converter via an automated fluid storage and injection system. precisely timed def injections elevate the temperature of the various filtration elements and allow them to perform more efficiently. introducing def into the catalyst system promotes filtration element longevity and allows fewer harmful exhaust emissions to be released into the atmosphere.
the eas and catalyst systems are monitored and controlled by either the pcm or a stand-alone controller (which interacts with the pcm). the controller monitors the reductant fluid injection system pressure, o2, nox, and exhaust temperature sensors (as well as other inputs) to determine the appropriate time for def (reductant) injection.
亚虎国际老虎机网站if the pcm detects excess voltage on the circuit for the eas fuel pressure sensor, a code p20e0 will be stored and a malfunction indicator lamp may be illuminated.
What is the severity of this DTC?
亚虎国际老虎机网站a stored code p20e0 should be considered severe and addressed as quickly as possible. the eas system may be damaged as a result of the conditions which contributed to the code p20e0 being stored.
What are some of the symptoms of the code?
symptoms of a p20e0 trouble code may include:
- Diminished engine performance
- Excessive black smoke from vehicle exhaust
- Reduction in fuel efficiency
- Other EAS/SCR related codes
What are some of the common causes of the code?
causes for this code may include:
- Defective EAS fuel pressure sensor
- Bad EAS fuel supply pump
- Open or shorted wiring in the EAS fuel pressure sensor circuit
- Bad EAS controller/PCM or programming error
What are some P20E0 troubleshooting steps?
a diagnostic scanner, a digital volt/ohmmeter (dvom), and a source of vehicle specific diagnostic information will be required to diagnose a code p20e0.
locating a technical service bulletin (tsb) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited, could yield helpful diagnostic information.
i like to begin my diagnosis with a visual inspection of the eas wiring harnesses and connectors. burnt or damaged wiring and or connectors should be repaired or replaced before proceeding.
i would continue by plugging the scanner into the vehicle diagnostic connector and retrieving all stored codes and pertinent freeze frame data. consider writing this information down before clearing the codes. test drive the vehicle until the pcm either enters readiness mode or the code is reset.
if the pcm enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose if this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.
if the code is immediately reset, completing the next step of your diagnosis will require that you search your vehicle information source to obtain diagnostic flow charts, connector pin-out charts, connector face views, as well as component testing procedures and specifications.
use the dvom to test (voltage drop) on all eas fuel supply system grounds. continue by testing the power supply to the eas control system. test fuses with the circuit loaded to avoid misdiagnosis.
亚虎国际老虎机网站if all system fuses are intact, use the dvom to test the eas fuel pressure sensor and sensor circuits. if any of these components fails to meet manufacturer’s specifications, suspect that it has failed.
- Don’t forget ground circuits when voltage drop testing
Related DTC Discussions
- There are currently no related topics in our forums. Post a new forum topic now.
Need more help with a P20E0 code?
If you still need help regarding the P20E0 trouble code, please post your question in our FREE car repair forums.
note: this information is presented for information purposes only. it is not intended as repair advice and we are not responsible for any actions you take on any vehicle. all information on this site is copyright protected.