P2A01 O2 Sensor Circuit Range/Performance Bank 1 Sensor 2
OBD-II Trouble Code Technical Description
ASE Certified Technician
亚虎国际老虎机网站o2 sensor circuit range/performance bank 1 sensor 2
What does that mean?
亚虎国际老虎机网站this diagnostic trouble code (dtc) is a generic powertrain code, which means that it applies to all 1996-newer vehicles (dodge, ford, chevy, kia, ram, honda, pontiac, etc.). although generic, the specific repair steps may vary depending on make/model.
亚虎国际老虎机网站in my experience, when an obd-ii equipped vehicle has stored a p2a01 code, it means that the powertrain control module (pcm) has detected a malfunction in the downstream (or post catalytic converter) oxygen (o2) sensor or circuit. bank 1 denotes the bank of the engine that contains the number one cylinder and sensor 2 indicates that the malfunction is related to the downstream sensor.
亚虎国际老虎机网站o2 sensors are made with a zirconium dioxide sensing element protected by a vented steel housing. the sensing element is attached to wire leads in the o2 sensor wiring harness using platinum electrodes. a controller area network (can) connects the pcm to the o2 sensor wiring harness. the o2 sensor provides the pcm with data regarding the percentage of oxygen particles in the engine exhaust as compared to the oxygen content of ambient air.
exhaust gases escape the engine into the exhaust pipe and through the catalytic converter; then pass over the downstream o2 sensor. as exhaust flows through the vent holes in the steel housing and across the sensing element, ambient air is drawn through the wire lead cavities and into a small chamber in the center of the sensor. in the chamber, the ambient air is heated by the exhaust, forcing the oxygen ions to produce (energy) voltage. variations between the number of oxygen molecules in ambient air (drawn into the o2 sensor) and the concentration of oxygen ions in the spent exhaust gases cause voltage levels to change.
A typical oxygen O2 sensor:
these changes cause the oxygen ions inside the o2 sensor to bounce between platinum layers very rapidly and repetitiously. voltage variations occur as the rushing oxygen ions bounce between platinum layers. the pcm recognizes these variations in voltage as changes in exhaust oxygen concentration. these changes indicate whether the engine is either running lean (too little fuel) or rich (too much fuel). the voltage signal from the o2 sensor is lower when more oxygen is present in the exhaust (lean condition) and higher when less oxygen is present in the exhaust (rich condition). this data is used by the pcm to calculate fuel delivery and ignition timing strategy. the upstream o2 sensor reacts with a lot of fluctuation normally, whereas the downstream should be more steady, if things are operating normally.
亚虎国际老虎机网站if the downstream o2 sensor circuit fails to respond as expected, over a set period of time and under certain programmed circumstances, a p2a01 code will be stored and a malfunction indicator lamp may be illuminated.
Severity & Symptoms
亚虎国际老虎机网站since a p2a01 code means that the downstream o2 sensor has failed to input an acceptable signal to the pcm, it should be considered severe.
亚虎国际老虎机网站symptoms of a p2a01 code may include:
- Diminished fuel efficiency
- A lack of general engine performance
- Other related diagnostic trouble codes may also be stored
- Service engine soon lamp illumination
possible causes for this engine code include:
- A failed O2 sensor
- Burnt, broken, or disconnected wiring and/or connectors
- Engine misfires
- Vacuum leaks
- Bad mass air flow or manifold absolute pressure sensor
- Engine exhaust leaks
Diagnostic and Repair Procedures
亚虎国际老虎机网站a good starting point is always to check for technical service bulletins (tsb) for your particular vehicle. your issue may be a known issue with a known fix put out by the manufacturer and can save you time and money during diagnosis.
亚虎国际老虎机网站i would require a diagnostic scanner, digital volt ohmmeter (dvom), and a reliable vehicle information source to diagnose a code p2a01.
misfire codes, throttle position sensor codes, manifold air pressure code, and mass air flow sensor codes should be diagnosed and repaired prior to diagnosing a code p2a01. the engine must be running efficiently before a successful diagnosis can be made.
professional technicians typically begin with a visual inspection of system wiring harnesses and connectors. focus on harnesses that are routed near hot exhaust pipes and manifolds, as well as those that are routed near sharp edges like the ones found on exhaust shields.
proceed by retrieving all stored trouble codes and freeze frame data by connecting the scanner to the vehicle diagnostic port. this information may be helpful if the p2a01 proves to be intermittent, so write it down. clear the codes and test drive the vehicle to see if the p2a01 is immediately reset.
should the p2a01 be reset, start the engine and allow it to reach normal operating temperature, then let it idle (with the transmission in neutral or park). bring up the scanner data stream and observe o2 sensor input data. narrow the data stream display to include only pertinent data so you can get a faster data response. if the engine is running efficiently, downstream o2 sensor data should fluctuate slowly and minimally. a p2a01 will be stored if the signal is outside expected parameters.
亚虎国际老虎机网站connect the dvom test leads to the sensor ground and signal wires in order to monitor live data from the o2 sensor. you may also be use the dvom to check resistance of the o2 sensor in question, as well as voltage and ground signals. prior to testing system circuit resistance with the dvom, disconnect all related controllers.
亚虎国际老虎机网站additional diagnostic notes:
- Low grade replacement catalytic converters are prone to repeated failure and should be avoided
Related DTC Discussions
- '06 Silverado v6 p0101 p0128 p2A01 p0300 heavy misfires
The CEL would turn and off randomly for a couple years without any noticeable engine issues. Recently I noticed a flashing CEL when I would accelerate over 1800 rpm or if I ran over 35 mph. I'm relatively clueless in regards to engine repair but I did replace the plugs (not the wires). I'm just look...
- 2007 chev Silverado 1500 classic P0101 P0172 P0175 P2A01
62000 miles codes come up only at hwy speeds. Checked for cracked and or leaking vacuum hoses cleaned mad sensor. It has K&N filter. Does not seem to run rough or any other noticeable problems...
- 2006 HHR codes P2A01, P0134, P0137
what do these codes mean and how can I fix the problem without costing me a lot of money? car is running fine its the engine light coming on is all. cannot get car inspected due to this...
Need more help with a p2a01 code?
If you still need help regarding the P2A01 trouble code, please post your question in our FREE car repair forums.
亚虎国际老虎机网站note: this information is presented for information purposes only. it is not intended as repair advice and we are not responsible for any actions you take on any vehicle. all information on this site is copyright protected.